Chrysler 3.6L V6 Pentastar Engine: Specs, Problems, Reliability, & More

Chrysler 3.6L V6 Pentastar Engine: Specs, Problems, Reliability, & More. The 3.6 L V6 Pentastar is a 3.6-liter six-cylinder gasoline engine introduced first at the New York Auto Show in 2009 for the 2011 model-year Chrysler, Dodge and Jeep vehicles. This new V6 is just one of the most technologically advanced engines to date, created by Chrysler. The V6 is used in popular cars around the world like the Dodge Challenger, Jeep Cherokee, Jeep Wrangler, and in the Ram 1500 truck. The 3.6 L Pentastar V6 for three years straight was among the top ten engines in the US market.

Chrysler 3.6L V6 Pentastar Engine

The new 3.6 V6 engine is 38% more powerful, consumes 11% less fuel, and 42 lbs (19 kg) lighter than its 3.5-liter predecessor. It is also smaller in size: 94 mm shorter than the 3.7 and 34 mm shorter than the 3.5 V6. The engine has a high-pressure die-cast aluminum cylinder block with 60-degree V angle between cylinder banks. It is an open-deck design, which saves material, lighter and cheaper to produce, and has cast iron cylinder liners for increasing longevity.

Chrysler 3.6L V6 Pentastar Engine

The engine block is equipped with three piston oil cooler jets. Each oil jet cools two pistons, prevent detonations, and controls heat. There are forged steel connecting rods, the nodular iron crankshaft, and cast aluminum pistons with low-friction rings and reduced skirt area for less weight and friction as well. The engine uses a chain-driven, vane-type variable displacement oil pump. Engineers removed all brackets for the engine accessories. The alternator, ac system compressor, and belt tensioner are bolted to the engine block. They are driven by a serpentine belt as well. This arrangement has significantly reduced the level of vibration and noise.

Read:  BMW M52B28 Engine: Specs, Problems, Reliability, & More

The 3.6 L Pentastar has sand-cast aluminum cylinder heads constructed from T7 heat-treated aluminum. Cylinder head feature 4-valve per cylinder and dual overhead camshafts with roller finger followers with hydraulic lifters. The intake and exhaust camshafts are chain-driven (there is a separate timing chain for every head). Timing chains are a “silent chain link” design. All four camshafts come with torque-actuated phasers. The intake valve is a single-piece design, constructed from forged heat resistant (martensitic) steel; intake valve diameter is 39 mm. The exhaust valves are two-piece designs, with a forged austenitic head welded to a martensitic stem; the exhaust valve diameter is 30 mm. Cylinder heads feature high-flow intake and exhaust ports, and an integrated exhaust manifold. On top of the engine, there is a lightweight composite intake manifold fitted with a 74 mm throttle body and an electronically controlled multi-point port fuel injection system.

90% of maximum torque is achieved in the range of 1800-6350 rpm. Thus, the engine can provide excellent driving dynamics without requiring high-octane (premium gasoline). While engines are sufficient simple in maintenance and not demanding on fuel quality, they feature great fuel efficiency, low emissions, and smooth operation. Pentastar V6 engines are very popular both in the United States and beyond. They meet Federal Tier 2 BIN 5 emission requirements, Ultra-low Emissions Vehicle II standards, and Euro6 standards. It is also designed to meet future strict standards including LEV III and PZEV California standards.

In 2016, FCA released upgraded Pentastar engine family and a new version of the 3.6 L V6 for the Jeep Grand Cherokee and Dodge Durango. The revised engine now has a two-stage variable valve lift (VVL). The VVL system provides low and high valve lifts. Low-lift settings at low speeds save fuel (up to 2.7% increase over the previous version), while high valve lift activates when power is needed. Unfortunately, the manufacturer was forced to install a cooled exhaust gas recirculation (EGR) system. The modified engine also features a new plastic intake manifold with longer runners increased torque, high-tumble intake ports inside cylinder heads, new valve springs, and low-tension piston rings. The fuel system received new eight-hole injectors. And the bright side is, the engine has kept a port fuel injection. The variable valve timing (VVT) system was recalibrated. The compression ratio was increased from 10.2:1 to 11.3:1. These improvements help to produce more power and torque along with better fuel efficiency, as well as reduce emissions.

Read:  VW/Audi 1.5 TSI EA211 Engine Specs, Problems, Reliability

In recent years, the Pentastar V6 engine successfully competes with the more technologically advanced 2.0 L turbo four – 2.0-liter Turbo Hurricane.

3.6 V6 Pentastar Engine Problems and Reliability

The left side cylinder head problem had been found in about 0.5% percent of 2011-13 vehicles with 3.6-liter V-6 Pentastar engines. Engines with cylinder head failure can be easily recognized by a ticking sound from the left side. Sometimes of them had other symptoms, including a check engine light illuminated. The failure was caused by excessive wear. In August 2012, Chrysler made the design upgrade and the problem is rarely reported now. All vehicles with 2011-13 model year 3.6 L Pentastar engines have extended engine warranty on the left side cylinder head to 10 years or 150,000 miles.

Some owners suffer problems with blocked radiators and frequent replacement of water pumps, thermostats, and oil pumps. The problem may depend on the production and preparation of an individual engine before assembly. The heads are sand-cast and undergo serious inspections for cleanliness before reaching assembly plants. But any residual sand that remains from the casting process inside the engine can also circulate through the vehicle’s cooling systems, causing clogs in radiator and oil cooling system.

Read:  Ford 2.0L Duratec HE Engine: Specs, Problems, and Reliability

In general, the engine has been around for a very long time and used in a lot of vehicles, so it has been well tested. Despite that they had some issues early on, the 3.6 L V6 Pentastar is a great engine, one of one of the most reliable engines available on the market right now.

Engine Specs

  • Manufacturer: FCA US LLC – Mack Avenue Engine Complex, Trenton Engine Plant and Saltillo South Engine Plant
  • Production years: 2010-present
  • Cylinder block material: Aluminum
  • Cylinder head material: Aluminum
  • Fuel type: Gasoline
  • Fuel system: Port multi-point fuel injection
  • Configuration VNumber of cylinders: 6
  • Valves per cylinder: 4
  • Valvetrain layout: DOHC
  • Bore, mm: 96.0 mm (3.78 in)
  • Stroke, mm: 83.0 mm (3.27 in)
  • Displacement, cc: 3,604 cc (219.9 cu in)
  • Type of internal combustion engine: Four-stroke, naturally aspirated
  • Compression Ratio: 10.2:1;
    11.3:1 – 2016+ the Gen2/revised Pentastar
  • Power, hp: 283-305 hp (211-224 kW)/6,350-6,600
  • Torque, lb ft: 251-269 ft-lb (340-365 Nm)/4,175-4,800
  • Engine weight: –
  • Firing order: 1-2-3-4-5-6
  • Engine oil weight: SAE 5W-20, 5W-30
  • Engine oil capacity, liter: 5.7 l (6.0 qt)
  • Oil change interval, mile: 9,000 (15,000 km) / 12 months
  • Applications: Jeep Grand Cherokee, Jeep Wrangler, Ram 1500, Ram ProMaster, Ram Cargo Van, Dodge Challenger, Dodge Charger, Dodge Durango, Dodge Avenger, Dodge Grand Caravan, Dodge Journey, Chrysler 300, Chrysler 200, Chrysler Town & Country, Chrysler Pacifica, Fiat Freemont, Lancia Thema, Lancia Voyager